SD Zinc 1500N 厚涂型無機富鋅底漆 1500N
PRODUCT DESCRIPTION A self-curing inorganic zinc coating based on alkyl silicate binder
& INTENDED USES
產品簡介 烷基硅酸酯為基料的自干型無機富鋅涂料。
FEATURES
產品特性
z Super resistance to corrosion
極好的防腐性能
z Outstanding resistance to impacts, mechanical abrasions and organic solvents
優良的耐沖擊、耐磨損和耐有機溶劑性能
z High-build applicability and good workability
極好的初始硬度
z High-build applicability and good workability
極好的厚涂施工性能
z Remarkable heat resistance
優良的耐熱性
z Compatible with blasted steel surfaces and inorganic zinc shop-primed surfaces
適用于預處理后的鋼材及無機富鋅車間底漆表面
BASIC DATA
基本數據
Color(s) Grey
顏色
灰色
Mixing ratio Liquid/Powder=20/80 (by wt.)
混合比率 液體/粉末=20/80（重量比）
Solids content 86%
重量固體份
Film thickness Dry : 30-100 microns/coat
涂裝膜厚 干膜: 30-100mm/道
Spreading rate Theoretical: 0.196 kg/ m ?2/40 microns
涂覆率 理論值 : 0.196 千克/平方米 40mm
Practical: Various depending on surface conditions, environment, applications,
etc.
實際值 : 與表面處理, 外界環境, 施工方法等多種因素有關。
STORAGE
儲存
Shelf Temperature -10℃-40℃
儲存溫度
Shelf life 6 months
儲存期限 6 個月
Flash point Greater than 20℃
閃點 20℃以上
APPLICATION DATA
施工數據
Pot Life
混合使用期
Temperature (℃)溫度 5 10 20 30
Pot life (hrs) 混合使用期 8 7 6 5
Application Methods
施工方法
Airless spray, air spray, brush and roller
無氣噴涂、空氣噴涂、刷涂及輥涂
Airless spray 無空氣噴涂 Recommended 推薦
Nozzle tip 噴嘴尺寸 0.021-0.023
Fluid pressure 出口壓力 75-125kg/cm
Thinning 稀釋比率 0-5% by volume（體積比）
Thinner SD Zinc 1500N Thinner
稀釋劑 專用稀釋劑
Application temperature -5℃-40℃
施工溫度
Drying time &
Overcoating interval
干燥時間&涂裝間隔
Temperature (℃) 溫度 -5 5 10 20 30
Dry to touch (hrs) 指觸干燥 90 60 60 30 20
Dry hard (hrs) 半硬干燥 8 6 4 3 1
Min. interval (hrs) 最小涂裝間隔 48 48 24 24 24
Max. interval (days) 最大涂裝間隔 - - - - -
PAINTING SYSTEM
涂裝配套
?
?Applied substrates Bare steel .
適用底材 裸鋼。
Subsequent coat Epomarine EX 500, Epomarine EX 600 or according to the coating
適用上涂 systems of Kansai.
Epomarine EX 500, Epomarine EX 600,? 或參考我司推薦配套。
SURFACE PREPARATION
表面處理
z Remove salt and other water-soluble contaminants by fresh water
hosing.
用清水沖去鹽份及其它水溶性污物。
z Degrease according to SSPC-SP1 solvent cleaning.
依照 SSPC-SP1 溶劑清洗標準除去油脂。
z Remove weld spatter and smooth weld seams and sharp edges.
除去焊接飛濺并處理焊縫、毛刺使其光順。
z Remove rust, mill-scale and damaged shop primer by blasting to
near white metal SSPC-10 or ISO Sa2.5 or better.
用噴砂方式除去鐵銹、氧化皮和損壞的車間底漆達到 SSPC-10 or
ISO Sa2.5 或更好。
z Remove dust and dirt by high-pressure air before paint application
用高壓空氣吹掃除去灰塵等污物。
z Be sure that the surface is clean and dry prior to application.
施工前確認表面清潔干燥。
vSAFETY PRECAUTIONS
安全措施 A health and safety data sheet for product is available upon request.
Minimum precautions to be taken in dealing with all paints are:
任何油漆施工中均應保證提供以下措施:
z Avoid skin and eye contact.
避免接觸皮膚和眼睛。
z If paint comes into contact with the skin , wash with warm water
and/or a suitable cleanser. If paint comes into contact with the eyes,
flush with copious amount of water and seek immediate medical
attention.
如果油漆接觸到皮膚，應用溫水以及（或者）適當的清洗劑清
洗。如果油漆接觸到眼睛，應用大量水沖洗并立即就醫。
z Ensure good ventilation.
保證良好的通風。
z Paint products contain flammable materials. Please keep them away
from sparks and prohibit any smoking in the vicinity.
涂料中含有可燃物質。請遠離火花并禁止在臨近地區吸煙。
z Observe all health and safety data on the container.
現場遵守一切健康安全規定。
DISCLAIMER The information given on this sheet is to the best of our knowledge and
提請注意 accurate at the time of printing. Since conditions of use are beyond the
manufacture's control, information contained herein is without
warranty, implied or otherwise, and the suitability of the material for
the use contemplated is the sole responsibility of the buyer. The
information contained on this data sheet is subject to modification at
any time due to our policy of modification and product development.
本說明書所提供信息均為目前我方所掌握最全面正確的資料,鑒于
產品使用條件非我方所能控制，此中信息不含擔保，即僅在選取產
品上對買方負責。由于我公司產品及生產工藝的不斷發展，此中所
有信息均以我方確認為主。
REMARKS As the drying time of this paint depends on the humidity of the air, so
備注
please consult Kansai's technical deputy for the practical drying time when
application.
該涂料的干燥時間與空氣相對濕度有關，施工時具體干燥時間需經我司技術代表
確認。
|
