SD Zinc 500
PRODUCT DESCRIPTION
& INTENDED USES
產品簡介
FEATURES
產品特性 |
|
環氧富鋅底漆 500
A high-build zinc rich primer based on epoxy resin for various of
coating systems |
厚涂型環氧富鋅底漆，可與多種涂料配套使用。 |
| |
z Remarkable corrosion resistance
極佳的防腐性能
z High build applicability
良好的厚涂施工性
z Quick drying
干燥迅速
z Excellent resistance to abrasions and impacts
極好的耐磨損、耐沖擊性能
z Long-term protection when used with epoxy
coatings
與環氧涂料配套時可提供長期的保護
|
|
BASIC DATA
基本數據
Color(s)
顏色
Mixing ratio
混合比率
Solids
content
重量固體份
Film
thickness
涂裝膜厚
Spreading rate
涂覆率 |
|
Grey
灰色
Base/Hardener=95/5 (by wt.)
主劑/固化劑=95/5（重量比）
87%
|
|
Dry : 30-80 microns/coat
干膜: 30-80mm/道 |
Wet : 52-138 microns/coat
濕膜: 52-138mm/道 |
|
Theoretical: 0.234kg/ m 2/50 microns
理論值 : 0.234/千克/平方米/50mm
Practical: Various depending on surface conditions, environment,
applications, etc.
實際值 : 與表面處理, 外界環境, 施工方法等多種因素有關。
|
|
STORAGE
儲存
Shelf
temperature
儲存溫度
Shelf life
儲存期限
Flash point
閃點
|
|
-10℃-40℃
6 months
6 個月
Greater than
18℃
18℃以上 |
|
|
|
|
|
|
| |
Temperature (℃)溫度
Pot life (hrs)
混合使用期 |
|
10
24 |
20
16 |
30
16 |
|
|
施工方法 |
|
| |
Airless spray, air spray, brush and
roller
|
無氣噴涂、空氣噴涂、刷涂及輥涂
Airless spray
Nozzle tip
Fluid pressure
Thinning |
|
|
Recommended 推薦
0.021-0.023
100-150kg/cm
0-5% by volume（體積比） |
|
|
Thinner
稀釋劑
Application
temperature
施工溫度
Drying time &
Overcoating interval
|
干燥時間&涂裝間隔 |
SD Zinc Thinner
環氧富鋅稀釋劑
-10℃-40℃ |
|
| |
Temperature (℃)
Dry to touch (mins)
Dry hard （hrs）
Min. interval (hrs)
Max. interval (days) |
溫度
指觸干燥
半硬干燥
最小涂裝間隔
最大涂裝間隔 |
|
|
|
|
|
|
|
PAINTING SYSTEM
涂裝配套
Applied substrates
適用底材
Subsequent coat
適用上涂 |
|
Bare steel.
裸鋼等。
Epomarine EX 500、Epomarine EX 600、Epomarine Super EX 21,
or according to the coating systems of Kansai.
Epomarine EX 500、Epomarine EX 600、Epomarine super EX21AC, 或參考我司
推薦配套 |
|
|
z Remove salt and other water-soluble contaminants by fresh water hosing.
用清水沖去鹽份及其它水溶性污物。
z Degrease according to SSPC-SP1 solvent cleaning.
依照 SSPC-SP1 溶劑清洗標準除去油脂。
z Remove weld spatter and smooth weld seams and sharp edges.
除去焊接飛濺并處理焊縫、毛刺使其光順。
z Remove rust, mill-scale and damaged shop primer by blasting to ISO
Sa2.5
(SSPC-SP10) or by power tooling to ISO St3.0.
用噴砂方式除去鐵銹、氧化皮和損壞的車間底漆達到 ISO Sa2.5 (SSPC-SP10)
或用電動工具處理表面達到 ISO St3.0。
|
|
|
SD ZINC 500
z Remove dust and dirt by high-pressure air before paint application
用高壓空氣吹掃除去灰塵等污物。
z Be sure that the surface is clean and dry prior to application.
施工前確認表面清潔干燥。
A health and safety data sheet for product is available upon request. Minimum
precautions to be taken in dealing with all paints are:
任何油漆施工中均應保證提供以下措施:
z Avoid skin and eye contact.
避免接觸皮膚和眼睛。
z If paint comes into contact with the skin , wash with warm water and/or a
suitable
cleanser. If paint comes into contact with the eyes, flush with copious amount of
water and seek immediate medical attention.
如果油漆接觸到皮膚，應用溫水以及（或者）適當的清洗劑清洗。如果油漆
接觸到眼睛，應用大量水沖洗并立即就醫。
z Ensure good ventilation.
保證良好的通風。
z Paint products contain flammable materials. Please keep them away from sparks
and prohibit any smoking in the vicinity.
涂料中含有可燃物質。請遠離火花并禁止在臨近地區吸煙。
z Observe all health and safety data on the container.
現場遵守一切健康安全規定。
The information given on this sheet is to the best of our knowledge and
accurate at the time of printing. Since conditions of use are beyond the
manufacture's
control, information contained herein is without warranty, implied or otherwise, and
the suitability of the material for the use contemplated is the sole responsibility
of the
buyer. The information contained on this data sheet is subject to modification at any
time due to our policy of modification and product development.
本說明書所提供信息均為目前我方所掌握最全面正確的資料,鑒于產品使用條件
非我方所能控制，此中信息不含擔保，即僅在選取產品上對買方負責。由于我
公司產品及生產工藝的不斷發展，此中所有信息均以我方確認為主。 |
|
