Eposeal 6000 PW
PRODUCT DESCRIPTION
& INTENDED USES
產品簡介
FEATURES
產品特性 |
|
EPOSEAL 6000 PW
環氧焦油涂料 6000 PW
A high-build isocyanate-cured epoxy tar coating
厚涂型異氰酸酯固化環氧焦油涂料。 |
|
| |
z Quick drying at low temperature
低溫下干燥迅速
z Outstanding corrosion resistance
優秀的防腐性能
z Suitable for crude oil loading and sea water immersion
適于儲存原油，可以承受海水浸泡
z Resistance to cathodic protection
耐陰極保護
z Excellent resistance to impacts and abrasions
極好的耐沖擊和耐磨損性能
z Excellent high-build applicability
極好的厚涂施工性
z Excellent compatibility with bare steel substrates and shop-primed
surfaces
同裸鋼底材及車間底漆的配套性極佳
|
|
基本數據
Color(s)
顏色
Mixing ratio
混合比率
Solid content
重量固體份
Film
thickness
涂裝膜厚
Spreading
rate
涂覆率 |
|
Black and Brown
黑色、棕色
Base/Hardener=10/1 (by wt.)
主劑/固化劑=10/1（重量比）
70%
|
00-250 microns/coat
干膜: 100-250mm/道 |
Wet : 172-431 microns/coat
濕膜: 172-431mm/道 |
|
Theoretical: 0.300kg/ m 2/125 microns
理論值 : 0.300 千克/平方米/125mm
Practical: Various depending on surface conditions, environment,
applications, etc.
實際值 : 與表面處理, 外界環境, 施工方法等多種因素有關。 |
|
STORAGE
儲存
Flash point
閃點
Shelf life
儲存期限
Shelf temperature
儲存溫度
APPLICATION DATA
施工數據
|
|
Greater than
2℃
2℃以上
1 year
1 年
-10℃-40℃ |
|
|
|
| |
Temperature (℃)溫度
Pot life (hrs) 混合使用期 |
|
|
|
|
|
|
|
| |
Airless spray, air spray, brush and roller
無氣噴涂、空氣噴涂、刷涂及輥涂 |
Airless spray
Nozzle tip
Fluid pressure
Thinning |
|
Recommended 推薦
0.023-0.029
100-150kg/cm
0-5% by volume（體積比） |
|
|
Thinner
稀釋劑
Application
temperature
施工溫度
Drying time &
Overcoating interval
干燥時間&涂裝間隔 |
|
Eposeal Thinner 20
環氧焦油稀釋劑 20
-10℃-15℃ |
|
| |
Temperature (℃)
Dry to touch (hrs)
Dry hard (hrs)
Before flooding (days)
Min. interval (hrs)
Max. interval (days) |
溫度
指觸干燥
半硬干燥
耐浸干燥
最小涂裝間隔
最大涂裝間隔
|
|
|
|
|
|
|
PAINTING SYSTEM
涂裝配套
Applied substrates
適用底材
Preceding coat
適用下涂
SURFACE PREPARATION
表面處理 |
|
Bare steel.
裸鋼。
SD Zinc 1000HA (S)or according to the coating systems by Kansai
SD Zinc 1000HA(S)，或參考我司推薦配套。 |
|
| |
z Remove salt and other water-soluble contaminants by fresh water hosing.
用清水沖去鹽份及其它水溶性污物。
z Degrease according to SSPC-SP1 solvent cleaning.
依照 SSPC-SP1 溶劑清洗標準除去油脂。
z Remove weld spatter and smooth weld seams and sharp edges.
除去焊接飛濺并處理焊縫、毛刺使其光順。
z Remove rust, mill-scale and damaged shop primer by blasting to ISO Sa2.5
(SSPC-SP10) or by power tooling to ISO St3.0.
用噴砂方式除去鐵銹、氧化皮和損壞的車間底漆達到 ISO Sa2.5
(SSPC-SP10) 或用電動工具處理表面達到 ISO St3.0。
z Remove dust and dirt by high-pressure air before paint application
用高壓空氣吹掃除去灰塵等污物。
|
|
|
EPOSEAL 6000 PW
z Be sure that the surface is clean and dry prior to application.
施工前確認表面清潔干燥。
A health and safety data sheet for product is available upon request. Minimum
precautions to be taken in dealing with all paints are:
任何油漆施工中均應保證提供以下措施:
z Avoid skin and eye contact.
避免接觸皮膚和眼睛。
z If paint comes into contact with the skin , wash with warm water and/or
a
suitable cleanser. If paint comes into contact with the eyes,
flush with
copious amount of water and seek immediate medical attention.
如果油漆接觸到皮膚，應用溫水以及（或者）適當的清洗劑清洗。如果
油漆接觸到眼睛，應用大量水沖洗并立即就醫。
z Ensure good ventilation.
保證良好的通風。
z Paint products contain flammable materials. Please keep them away from
sparks and prohibit any smoking in the vicinity.
涂料中含有可燃物質。請遠離火花并禁止在臨近地區吸煙。
z Observe all health and safety data on the container.
現場遵守一切健康安全規定。
|
|
|
The information given on this sheet is to the best of our knowledge and
accurate at the time of printing. Since conditions of use are
beyond the
manufacture's control, information contained herein is without
warranty,
implied or otherwise, and the suitability of the material
for the use
contemplated is the sole responsibility of the buyer. The information
contained
on this data sheet is subject to modification at any time due to our policy of
modification and product development.
本說明書所提供信息均為目前我方所掌握最全面正確的資料,鑒于產品使
用條件非我方所能控制，此中信息不含擔保，即僅在選取產品上對買方負
責。由于我公司產品及生產工藝的不斷發展，此中所有信息均以我方確認
為主。
It is recommended to use standard type (Eposeal 6000 PS) when the
temperature is over 10℃.
當溫度達到 10℃以上時建議使用常規型產品(Eposeal 6000 PS)。 |
|
| |
|
